البحوث المنشورة لقسم هندسة المواد 2016

رجوع


اسم البحث اسم الباحث / الباحثين  جهة النشر / المجلة  سنة النشر  خلاصة البحث  قيمة المعامل التاثير 
Behavior of Ti/HA in Saliva at Different Temperatures as Restorative Materials ا.م.د.رنـا عفيف مجيد مجلة J Bio Tribo Corros العالمية 2016 دراسة السلوك التاكلي لمواد متراكبة في اللعاب الصناعي عند درجات حرارية مختلفة  
Sumac (Rhus) Extract as Green Inhibitor for Steel in Seawater ا.م.د.رنا عفيف مجيد International Journal of Scientific Research in Science 2016 استخدام مستخلص السماق المائي كمثبط للفولاذ في وسط ماء البحر المختبري
عند درجة حرارة المختبر وتم اضافة خمسة تراكيز مختلفة 4 و6 و8 و12 و16 مل لتر
 لكل لتر وتم تطبيق ايزوثيرك لانكماير وفحص مطيافية الاشعة تحت الحمراءللطبقات المتكونة بعد الغمر.
 
Sumac (Rhus) Extract as Green Inhibitor for Steel in Seawater م.م.هبة انور عبد الله  International Journal of Scientific Research in Science 2016 استخدام مستخلص السماق المائي كمثبط للفولاذ في
 وسط ماء البحر المختبري عند درجة حرارة المختبر وتم اضافة خمسة تراكيز مختلفة
 4 و6 و8 و12 و16 مل لتر لكل لتر وتم تطبيق ايزوثيرك لانكماير وفحص مطيافية
 الاشعة تحت الحمراءللطبقات المتكونة بعد الغمر.
 
Sumac (Rhus) Extract as Green Inhibitor for Steel in Seawater المهندس محمد علي طارق  International Journal of Scientific Research in Science 2016 استخدام مستخلص السماق المائي كمثبط للفولاذ في وسط ماء البحر المختبري عند درجة
 حرارة المختبر وتم اضافة خمسة تراكيز مختلفة 4 و6 و8 و12 و16 مل لتر لكل
 لتر وتم تطبيق ايزوثيرك لانكماير وفحص مطيافية الاشعة
تحت الحمراءللطبقات المتكونة بعد الغمر.
 
expermental and numerical study of buckling for carburized low carbon steel couumns  م.محمد كشكول علوان  الهندسة والتكنولوجيا  2016 the effects of sewage sludge ash ( SSA) AND SILICON
 CARBIDE ( SiC) PARTICLES
MECHANICALE PROPERTIES OF S-
GLASS FIBER REINFORCED EPOXY COMPOSITES WERE INVESTIGATE
COMPOSITE
LAMINATE SAMPLES FOR TENSILE AND FLEURAL EPOXY
 
Mechanical properties and mixed-mode fracture toughness
 ( I+III ) of silica nanoparticales reinforced polymer composite 
م.محمد كشكول علوان  الهندسة والتكنولوجيا  2016 the effects of sewage sludge ash ( SSA) AND SILICON CARBIDE ( SiC)
PARTICLES MECHANICALE PROPERTIES OF S-GLASS FIBER REINFORCED
EPOXY COMPOSITES WERE INVESTIGATE COMPOSITE LAMINATE SAMPLES
FOR TENSILE AND FLEURAL EPOXY 
 
A comparative study on industrial waste fillers affecting
 mechanical properties of polymer- matrix composites 
م.محمد كشكول علوان  الهندسة والتكنولوجيا  2016 expimental work and finite element techniques
 were used to anlyze the tensile and buckling
characteristics of carburized low carbon
steel columns for different diameters
0.968
effect of olive pomace on the
mechanical property of glass fiber reinforced epoxy composites 
م.محمد كشكول علوان  الهندسة والتكنولوجيا  2016 this work aims to study the effct of the mixing of
natural particles of micro - size olive pomace (op) on the
tensilie and flexural properties of glass fiber reinforced
 polymer composite (GFRP)
 
Tensile and flexural behavior of nano-silica
modified carbon/Kevlar hybrid composites 
م.محمد كشكول علوان  الهندسة والتكنولوجيا  2016 THE perpose of this articlee is to investigate the artiicle is
 to investigate the effect of different particle contents of nano-silica on the
 tensile and flexural properties of intralaminar
 carbon / kevlar hybride composite 
 
A COMPARSTIVE STUDY ON SEWAGES ASH APPECTING
MECHANICAL
PROPERTIES OF GLASS FABRIC/ EPOXY COMPOSITES 22
م.محمد كشكول علوان  الهندسة والتكنولوجيا  2016 the effect s of sewage sludge ash (SSA) and silicon
carbide ( SiC) Prticles michanical
propertiies of S-GLASS FIBER REINFORCED EPOXY COMPOSITETES WERE
INESTIGATE COMPOSITE LAMINATE SAMPLES FOR
TENSILE AND FLEXURAL WERE PREPERD AND TESTED CCCORDING M  standareds tests
 
A STUDY ON PERLITE PARTICAL PROPERTIES OF
GLASS FIBRIC / EPOXY COMPOSITES
م.محمد كشكول علوان  الهندسة والتكنولوجيا  2016 THE effect of perlite (Pr) and silicon carbide ( SiC)
PARICLES ON THE MECHANICAL PROPERTIES OF s-GLASS
 FIBER REINFORCED EPOXY COMPOSITES WERE
 INVESTIGATED
 
      2016    
fabrication of TiO2 ,
 V2O5 Thin film ( super
hydrophobic surface )
by powder coating technique
  مجلة JOURNAL OF ENGINEERING 2016    
fabrication of TiO2 , V2O5 Thin film ( super
hydrophobic surface ) by powder coating technique
ا.م.د.رنا عفيف مجيد مجلة JOURNAL OF ENGINEERING 2016 دراسة السلوك التاكلي لمتراكبات ذات اساس
 تيتانيوم مدعمه بالهيدروكسي اباتيت لاستخدامها في مجال
 طب الاسنان
 
fabrication of TiO2 , V2O5 Thin film ( super hydrophobic
surface ) by powder coating technique
ا.م.د.علاء حسن علي  مجلة JOURNAL OF ENGINEERING 2016 دراسة السلوك التاكلي لمتراكبات ذات اساس تيتانيوم
 مدعمه بالهيدروكسي
 اباتيت لاستخدامها في مجال طب الاسنان
 
Effects of High Voltage and Flow Rate Parameters on Nanofibers
Diameter Synthesis by Electrospinning Technique
ا.م.د.اكرم رحيم جبر  . Journal of Physical Science and Application 2016 Nylon 6 / chitosan membreanes were
fabricated bt electrospinning onto a millipore glass
fibed filter to produce nanofibrous filter.
 
  ا.م.د.ليث قيس عباس    2016 Nylon 6 / chitosan membreanes
were fabricated bt electrospinning onto a millipore glass fibed filter to
produce nanofibrous filter.
 
Characterization of Aluminum-Silver Nano Films and Its Effect as
Antimicrobial
 and Degradation of Organic Compounds
أ.م.د. ألاء عـلاء الدين Journal of Physical Science and Application
 
2016 في هذا البحث تم تحضير أغشية رقيقة من الألمنيوم بطريقة الرش مع إضافة دقائق الفضة
النانوية ( 50 nm)  بنسب مختلفة (0, 25, 50, 75, 100%)  لتحضير متراكب   Al - Ag   على قواعد من الشرائح
 الزجاجية  .أجريت فحوصات  XRDو  SEM  للنماذج و من ثم الاختبارات التطبيقية
لهذه الأغشية من حيث الفاعلية البيولوجية و تأثير
 الضوء علاوة على تحلل صبغة المثيل الزرقاء
Volume 6,
 Number 1, January
2016 (Serial Number 31)
Estimation the Efficiency of Nano Particles

Coating on Carbon Steel by
Atomization
ا.م.د.رنا عفيف مجيد   2016 يتضمن هذا البحث دراسة السلوك التاكلي للصلب
الكاربوني المطلي بمواد نانوية في وسط ماء البحر 
 
Estimation the Efficiency of Nano Particles
Coating on Carbon Steel by Atomization
ا.م.د.احمد محمد حسن الغبان  مجلة الهندسة والتكنولوجيا  2016 يتضمن هذا البحث دراسة السلوك التاكلي للصلب الكاربوني المطلي بمواد نانوية في وسط ماء البحر   
effect of MWCNT addition on improving the
electrical conductivity
 and activation energy of electrospun nylon films 
ا.م.د.اكرم رحيم جبر  krrbala international journal of modern science  2016 Nylon6/with (0.0.1.0.22.0.4.0.40.6
 and 0.8)wt.% MWCNTS films conductive polymer
were by electrospining technique. Prepared films morphology test by SEM
and the average fibers dimeters measure conductivity by incrasing
 MWCNTS  concentration from ( 2.9 - 10.S/cm ) for pure nylone
filme to ( 1.042 - 10 - s/cm )
 for 0.8 wt.% MWCNT. 
 
effect of MWCNT addition on improving the electrical
conductivity
 and activation energy of electrospun nylon films 
ا.د.فاضل عطية جياد  krrbala international journal of modern science 2016 Nylon6/with (0.0.1.0.22.0.4.0.40.6 and 0.8)wt.% MWCNTS
 films conductive polymer were by electrospining technique. Prepared
films morphology test by SEM and the average fibers dimeters measure conductivity
by incrasing MWCNTS  concentration from ( 2.9 - 10.S/cm ) for pure
nylone filme to ( 1.042 - 10 - s/cm ) for 0.8 wt.% MWCNT.
 
the microstructure and magnetic
 
characterization of nikel ferrite nanofibers 
ا.م.د.اكرم رحيم جبر  the iraqi journal of mechanical and materials Eng.  2016 the nano nickel-zinc ferrite ( NiFe2O4) was
prpred by electrospinning technique,nikel nitrate hexahydrate, iron
nitrate nonahydrate, polyvinylprrolidone PVP and N, N-dimethy informamide ( DMF )
were used as precururosor materials
 
the microstructure and magnetic
 
characterization of nikel ferrite nanofibers 
ا.د..فاضل عطية جياد  the iraqi journal of mechanical and materials Eng.  2016 Nylon6/with (0.0.1.0.22.0.4.0.40.6 and 0.8)wt.% MWCNTS films conductive
 polymer were by electrospining technique. Prepared films morphology test
by SEM and the average fibers dimeters measure conductivity
by incrasing MWCNTS  concentration from ( 2.9 - 10.S/cm ) for pure
nylone filme to ( 1.042 - 10 - s/cm ) for 0.8 wt.%
MWCNT. 
 
effect of NaCl solution addition on
imroving some
 of the physical
properties of Nylon6 solutions used for
electro spining purpose 
ا.م.د.اكرم رحيم جبر  eng.&Tech.jounal  2016 nylon 6/ ( 0.5.1.1.5.2.and 2.5)wt.% NaCl solutions were
 prepared for electrospininng technique. The
electrical xonductivity of polymeric solution increases directly with NaCl concentrration
from 3.8 ( Ms / cm ) for pure nylon solutions to 12.7 ms/cm at nylon 6/2.5 wt.% NaCl, and
slight decreasing the viscosity and the surface tension of the
solution 
 
effect of NaCl solution addition on imroving
 some of the
physical properties of Nylon6 solutions used for
electro spining purpose 
ا.د.فاضل عطية جياد  eng.&Tech.jounal  2016 nylon 6/ ( 0.5.1.1.5.2.and 2.5)wt.% NaCl solutions were
 prepared for electrospininng technique. The electrical xonductivity
of polymeric solution increases directly with NaCl concentrration from 3.8 ( Ms / cm ) for
pure nylon solutions to 12.7 ms/cm at nylon 6/2.5 wt.% NaCl, and
slight decreasing the viscosity and the surface tension of the
solution 
 
Ambient Temperature Affect the pore
size of PVA Nanofibers Tissues 
ا.م.د.اكرم رحيم جبر  eng.&Tech.jounal  2016 electrospining has recently emerged as a leading
 technique for generating
 biomimetic scaffolds made of synthetic
and natural
polymeres for tissue engineering applications. PVA was dissolved in distilled water at concentration (
10% wt). PVA 10% DW solution
 was prepared as bioolymeric materials for fabricating tissue engineered scaffolds by
electrospining
 , varying ambient temperature ( 25.30.35.40.45 and 50)C and investigated the ambient tempearature
effect on tissue nanofibers pore size. scaninng electron microscopy
 was
ultilized to profile the topography of individual electrospun fibers.
 
Ambient Temperature Affect the pore
size of PVA Nanofibers Tissues 
ا.م.د.ليث قيس عباس  eng.&Tech.jounal  2016 nylon 6/ ( 0.5.1.1.5.2.and 2.5)wt.% NaCl solutions
were prepared for electrospininng technique. The electrical xonductivity
of polymeric solution increases directly with NaCl concentrration from 3.8 ( Ms / cm ) for
pure nylon solutions to 12.7 ms/cm at nylon 6/2.5 wt.% NaCl, and
slight decreasing the viscosity and the surface tension of the solution 
 
the microstructure and characterization of nikel firritr nanofibers  ا.م.د.اكرم رحيم جبر  ADVANCECES IN NATURAL AND APPLIED
 SCIENCES/ PUBLISHED BY AENSI PUBLICATION
2016 One-dimensional (1D) nanomaterials such as nanotubes
, nanowires, nanofibers and nanobelts have
drawn considerable attention over the past few decades
 
ADVANCECES IN NATURAL AND APPLIED SCIENCES/ PUBLISHED BY AENSI PUBLICATION ا.د.فاضل عطية جياد    2016 One-dimensional (1D) nanomaterials such as
nanotubes, nanowires, nanofibers and nanobelts have drawn
considerable attention over the past few decades
 
Fabrication of electrospun chitosan/Nylon6 Nanofibrous
 membrane
 toward metal irons removal and antibacterial effect
Fabrication of electrospun
chitosan/Nylon6
Nanofibrous membrane toward metal irons
removal and antibacterial 
ا.م.د.اكرم رحيم جبر  hindawi publishing corporation/ advances in materials
scince and engineering 
2016 Bacterial water pollution of is a genuine
general wellbeing concern since it causes various maladies.Antimicrobial
nanofibers can be integrated by incorporating 
nanobiocides, for example, silver
 
  ا.م.د.ليث قيس عباس  hindawi publishing corporation/ advances
 in materials scince and engineering 
2016 Bacterial water pollution of is a genuine
general wellbeing concern since it causes various maladies.Antimicrobial nanofibers can be
integrated by incorporating  nanobiocides, for example, silver
 
فصل في كتاب عالمي بعنوان tribocorosion  ا.م.د.رنا عفيف مجيد دار النشر intech  2016 المشاركة في تاليف فصل في كتاب عالمي   
فصل في كتاب عالمي بعنوان tribocorosion  ا.م.د.ماجد حميد عبد المجيد دار النشر intech 2016 المشاركة في تاليف فصل في كتاب عالمي   
physical properties estimation of Ti/HAP Functionally
 graded material by artificial neural network 
ا.م.د.رنا عفيف مجيد مجلة الهندسة والتكنولوجيا  2016 تقييم خواص مواد متدرجة التركيب من خلال استخدام الخلايا العصبية   
physical properties estimation of Ti/HAP
 Functionally graded material by artificial neural network 
ا.م.د.جواد كاظم عليوي  مجلة الهندسة والتكنولوجيا  2016 تقييم خواص مواد متدرجة التركيب من خلال استخدام الخلايا العصبية   
effect of tempering on thermal analysis of
Al-Ti-Si alloy and its comopsites
ا.م.د.رنا عفيف مجيد iraqi journal of physics  2016 دراسة السلوك التاكلي لمتراكبات ذات اساس المنيوم   
effect of tempering on thermal analysis
 of Al-Ti-Si alloy and its comopsites
ا.م.د.وفاء مهدي صالح iraqi journal of physics 2016 دراسة السلوك التاكلي لمتراكبات ذات اساس المنيوم   
the effect of Te Addion on shape memory
 properties on CU-Al-Ni shape memory alloys 
ا.م.د.رعد سهيل احمد حافظ internaional journal of advances
 in sciences engineering and technology ( IJASEAT ) 
2016 this paper aims to study the effect of trillium
 on thermo-mechanical charracterization by add Te with three
different weight percentages (0.3% , 1%, 3%) to a Cu-14% Al-405%Ni shape memory alloy
 wich prepared by casting method in vacuum induction
funace. Many testes and inspectings such as optical and SEM examinations, DSC
Measurement , XRD inspection, compression and vickers hardness tests
wewe investigated.
2.05
characterization of Nano powder
incorporated for construction applications 
ا.م.د.الاء علاء الدين عبد الحميد الهندسة والتكنولوجيا  2016 ي هذا البحث تم ترسيب اوكسيد التيتانيوم ( TIO2 )
واكسيد الفناديوم ( V2O5)
 بشكل غشاء
 رقيق عند نسبة خلط متخلفة
 ( 0و 25 و 50 و 75 و 100 ) % منها على قاعدة من الزجاج وبسمك طلاء
 ( 50 نانومتر ) في هذا البحث تم قياس زاوية الاتصال
 
characterization of Nano powder incorporated for
 construction applications 
ا.م.د.فرهاد محمد عثمان  الهندسة والتكنولوجيا  2016 ي هذا البحث تم ترسيب اوكسيد التيتانيوم ( TIO2 )
 واكسيد الفناديوم
 ( V2O5) بشكل غشاء رقيق عند نسبة خلط متخلفة
( 0و 25 و 50 و 75 و 100 ) % منها على
قاعدة من الزجاج وبسمك طلاء
( 50 نانومتر )
 في هذا البحث تم
قياس زاوية الاتصال
 
fabrication of TiO2 , V2O5 Thin film ( super
 hydrophobic surface ) by powder coating technique
ا.م.د. ألاء علاء الدين عبد الحميد،   2016 ي هذا البحث تم ترسيب اوكسيد التيتانيوم ( TIO2 ) واكسيد الفناديوم ( V2O5) بشكل غشاء رقيق عند نسبة خلط متخلفة
 ( 0و 25 و 50 و 75 و 100 )
 % منها على قاعدة من الزجاج وبسمك طلاء ( 50 نانومتر )
 في هذا البحث تم قياس زاوية الاتصال
 
fabrication of TiO2 , V2O5 Thin film ( super
 hydrophobic surface ) by powder coating technique
ا.م.د.فرهاد محمد عثمان   مجلة JOURNAL OF ENGINEERING 2016 في هذا البحث تم ترسيب اوكسيد التيتانيوم ( TIO2 ) واكسيد الفناديوم ( V2O5)
 بشكل
غشاء رقيق عند نسبة خلط متخلفة ( 0و 25 و 50 و 75 و 100 ) % منها على قاعدة من
الزجاج وبسمك طلاء
 ( 50 نانومتر ) في هذا البحث تم قياس زاوية الاتصال
 
physical and mechanical properties
 estimation of Ti/Hap functionally graded material using artificial
neural network 
ا.م.د.جواد كاظم عليوي  eng.&Tech.jounal  2016 this study presents the effort in applying neural
 network-based system indtification techniques by using back-
peopagation algorrithm to predcit some physical mechanical properties of
functionally graded and composite samples from Ti/HAP, theses samples were
fabricated by powder metallurgy method at various volum fraction of hydroxyapatite and
at n equal ( 0.8 , 1 , and 1.2 )
 
physical and mechanical properties estimation of
 Ti/Hap functionally graded material using artificial neural network 
ا.م.د.رنا عفيف مجيد eng.&Tech.jounal  2016 this study presents the effort in applying neural
network-based system indtification techniques by using back-peopagation algorrithm
to predcit some physical mechanical properties of functionally graded and composite samples
 from Ti/HAP, theses samples were fabricated by powder metallurgy method at various volum fraction
of hydroxyapatite and at n equal ( 0.8 , 1 , and 1.2 )
 
design of prothesthetic foot from polymer
 materials reinforced by carbon fibers 
ا.م.د.جواد كاظم عليوي  eng.&Tech.jounal  2016 design of prosthetic foot from polymer
materials reinforced by carbon fibers 
 
tensile poperties distribution
 of coir natural fiber using weibull statistics 
ا.م.د.جواد كاظم عليوي  eng.&Tech.jounal  2016 tensile properties distribution of coir
natural fiber using weibull statistics 
 
study the effect of iron powder additives on
 mechanical properties of recycling of aluminum cans scrap 
ا.م.د.جواد كاظم عليوي  eng.&Tech.jounal  2016 study the effect of iron powder additives on mechanical properties
of recycling of aluminum cans scrap 
 
study the effect of iron powder additives on
 mechanical properties of recycling of aluminum
cans scrap 
ا.م.د.فرهاد محمد عثمان  eng.&Tech.jounal  2016 study the effect of iron powder additives on mechanical properties
of recycling of aluminum cans scrap 
 
studying the tensile and bukling for PMMA Reinforced by jute fibers for prothetic pylon  ا.م.د.جواد كاظم عليوي  eng.&Tech.jounal  2016 studying the tensile and buckling for PMMA Reinforced by jute
fibers for prostheetic pylon
 
studying the tensileproperties and
morphology teast for the self cured PMMA Resing of prosthetic
compolelet denture.
ا.م.د.جواد كاظم عليوي  the iraqi journal of mechanical and materials Eng.  2016 studing the tensile properties and morphology
test for the self cured PMMA Resin of prosthetic compolete denture
 
studying the tensileproperties and
morphology teast for the self cured PMMA
 Resing of prosthetic compolelet denture.
 .م.د.قحطان عدنان حمد the iraqi journal of mechanical and materials Eng.  2016 studing the tensile properties and morphology test for the self cured
PMMA Resin of prosthetic compolete denture
 
tensile and fracture properties of coir
fiber green composites bone plate fixation 
ا.م.د.جواد كاظم عليوي  zanco journal of pure and applied sciences  2016 tensile and fracture properties
of coir fiber green composites bone plate fixation 
 
biomechaniics of natural
fiber green composites as internal bone plate rafted 
ا.م.د.جواد كاظم عليوي  MATEC Web of confernces  2016 biomechanics of natural fiber green
composites as internal bon plate rafted 
 
تصنيع وتوصيف اكاسيد ثلاثية معدنية
 بتقنية الرش الكيميائي الحراري كمتحسس غازي 
ا.م.د.فرهاد محمد عثمان  مجلة الخوارزمي الهندسية  2016 في هذا البحث حضرت اكاسيد ثلاثية بطريقة الرش الكيميائي الحراري البيسطة من املاح
( نترات القصدير والزنك والكامديوم ) بتركيز (0.1 M ) وبنسب خلط وزنية 50:50على قاعدة من
السيلكون نوع ( N) باتجاه (111) ( بوجود وبعدم وجود الحزوز وبالابعاد الاتية عرض 20 وعمق
 7.5 ككاشف للغاز بتراكيز مختلفة ( 10.50.100.500 ) في الهواء وبدرجة حرارة الغرفة والمرتبطة مع الصناعة النفطية.
 
ا.م.د.الاء علاء الدين عبد الحميد مجلة الخوارزمي الهندسية  2016 في هذا البحث حضرت اكاسيد ثلاثية بطريقة الرش الكيميائي الحراري البيسطة من املاح
 ( نترات القصدير والزنك والكامديوم ) بتركيز (0.1 M ) وبنسب خلط وزنية 50:50على
قاعدة من السيلكون نوع ( N) باتجاه (111) ( بوجود وبعدم وجود الحزوز وبالابعاد الاتية عرض 20
وعمق 7.5 ككاشف للغاز بتراكيز مختلفة ( 10.50.100.500 ) في الهواء وبدرجة حرارة الغرفة
والمرتبطة مع الصناعة النفطية.
 
ِfabrication of Tio2 , V2O5 thin film
( super hydrophobic surface )
by powder coatting technique
ا.د.محمد صلاب حمزة مجلة الهندسة والتكنولوجيا 2016    
fabrication of Tio2 , V2O5 thin film ( super hydrophobic surface ) by powder coatting technique ا.م.د.الاء علاء الدين عبد الحميد مجلة الهندسة والتكنولوجيا  2016    
international Journal of Advances in Sciences
, Engineering and Technology ( IJASEAT ) 
م.رعد سهيل احمد  مجلة الهندسة والتكنولوجيا  2016 THIS paper aims to study the effect of trillium on thermo-mechanical
charracterization by add Te with three different weight
percentages (0.3% , 1%, 3%) to a Cu-14% Al-405%Ni shape memory
alloy wich prepared by casting method in
vacuum induction funace. M
 
THE  EFFECT OF THERMO-
MECHANICAL TREATMENT ON CU-BASED SHAPE MEMORY  
م.رعد سهيل احمد  مجلة الهندسة والتكنولوجيا  2016